Synergy Products is now a Premium Wholesale Partner for Flange Wizard in Canada. We are stocking a large inventory of the most common products in our Edmonton warehouse. See below for all available in stock products. Other products are also available as Special Order items.
Two-Hole Pins (set of 2) #42050-T (threaded) for flanges with holes ½” to 1-7/16” in diameter. **
#42050-TL (large threaded) is for flanges with holes up to 1-15/16” in diameter. **
Two-Hole Pins (set of 2) #42050-TM (threaded – MINI) for flanges with holes 5/16″ to 63/64″ in diameter. Stud has a 5/16-18 thread.
Above models have one pin that has a 360° vial for easier vertical leveling that “snap” in and out for easy replacement.
#42050-TL (Large threaded)
Pins shown in flange with Pocket-Pro-Level on top for horizontal leveling of holes in flange.
#42050-TXL (extra large threaded) is extra large and designed to be light weight for easier handling. Extensions are included to accommodate thicker flanges. Works with flange holes 5/8” to 3.0” dia. Comes in sturdy polypropylene lockable case (p/n 8902).
All models are machine from hardened steel to make a very sturdy and lasting tool. Threaded models have fast double lead threads.
Extensions available for threaded models to accommodate thicker flanges:
2-7/8” Stud #0501
4-1/2” Stud #0503
Flange Wizard uses double lead fast threads instead of ACME threads because they are as fast, if not faster, to screw on and more importantly, we have found that ACME threads tend to loosen easier thus don’t hold job as secure as our double lead fast threads.
**NOTE: -TXL model fits flanges with hole sizes to 2-7/8″ in diameter. Refer to Flange Hole Diameter Reference Chart to check hole diameter.
#38240-T (threaded) – in protective carrying case with knurled nuts will fit flanges with holes from 1/2” to 1-7/16” diameter.**
#38240-TL – in sturdy cardboard box is the largest model. Fits flanges with holes 1/2” to 1-15/16” in diameter. **
All models of the Pipe Aligner will two-hole (make 2 holes of the flange horizontally level with the ground) and vertically level the face of the flange in ONE easy step.
Threaded models have fast release double lead threads.
All models have one pin that has a 360° vial for easier vertical levelling that just “snaps” in and out for easy replacement.
The Pipe Flange Aligner saves valuable fit-up time, in most cases it cuts fit-up time in half and eliminates the frustration of balancing a level on the pins.
All models are machined from steel to make a very sturdy and lasting tool.
Extensions are available for threaded models to accommodate thicker flanges:
2-7/8” Stud #0501
4-1/2” Stud #0503
*Protective carrying case (16″ x 6″ x 3″) #8903 can be ordered separately
Shown with block placed in various positions on cutting rail and with the 24″
Used as a cutting guide for conventional torch
Used as a cutting guide for plasma torch.
Magnetic Torch Guide #23040 This 24” stainless steel straight edge rail comes with two (2) strong, heat resistant, adjustable, magnetic blocks that can be positioned to accommodate any cutting job.
The 24″ Extension #23040-24 comes complete with one (1) magnetic connecting block and a 24″ cutting rail.
The connecting blocks are slotted on three (3) sides giving them the capability to fasten to your cutting rail in whatever position your job requires.
#24219 The Chariot Cutting Guide is a must for every tradesmen who uses a conventional cutting torch. It will cut circles up to 39″ in diameter. It can cut holes as small as 5/8″ when used without the axles. It can bevel circles up to 36″ in diameter. Cut straight, irregular shapes, circles and bevel with this versatile tool.
* Plated steel construction at heat stress points
* Universal bushing fits all conventional torches
* 15-1/2” extension (p/n 3311-EX) is available for larger circles
#28439 As a circle layout tool with sliding soapstone holder and 360° scale on the magnetic base. Will cut circles up to 30” in diameter (recommend Chariot Cutting Guide P/N 24219 for larger circles). Bolt circles, hole locations, baffle plate placement, and circle sectioning for any number of reasons is a snap with flange wizard®’s layout scale and sliding soapstone holder.
As a circle burning guide, use this same tool to cut a round plate; simply place the sharpened pin of the layout tool into your center punch mark and let the magnet slide down to sit firmly on the work surface. The magnet is strong enough to support the weight of your torch, which frees your hands for more cutting control.
WARNING: Never use the magnetic base or suction cups when cutting small holes. The heat will damage the magnets or the rubber suction cups. NOTE: You can cut holes as small as 4″ when you remove the base.
Magnetic Blocks #3-28 (3 per set) Magnetic Support blocks can be attached to any standard square or straight edge (up to 1/8′ thick) to form your own burning guides.
Blocks are machined aluminum and have thumb screws to easily adjust blocks on straight edges or squares.
#5102 This handy repair kit will make your flange wizard® hand tools like new again. Repair kit makes for easy repairs to your tools without delay. You receive a tube of sealant and two (2) replacement vials.
Remove the damaged or broken vial. Do this by cutting around the sealant plug and removing all the materials from the machined hole or slot. Place a small amount of sealant in the bottom of the hole or slot and install new vial. Fill remainders of the hole with sealant and wipe away the excess. Let sealant set up over night and your tool is ready to use again!
#53025-M (small magnetic) (for pipes 1-1/2” to 10” in diameter). Designed for the person who works with smaller diameter pipe. Fire protection contractors, fence and gate builders, live stock pens and corrals, and various alignment jobs in the automotive field are a few of the many uses.
#53076-M (standard magnetic)(for pipes 8” to 48” in diameter). Designed to establish and mark a center line at any angle around the circumference (inside and out) on a pipe or tank. This tool is a must for the welder’s or fitters’ toolbox.
Both tools are machined from quality aluminum material then anodized for lasting protection. They have a one piece “Y” shaped body design with a 2-1/2° increment degree dial that turns 360°’s. The degree dial has a built-in dial for leveling the tool at various angles. The hardened center punch marks your set position by taping with a hammer (vial and center punch are replaceable for lasting service). Magnets in the legs will free up the users hands for a safer and more accurate layout mark. Use them to establish and mark a center line at any angle around the circumference on a pipe or tank or as a protractor level.
#63803 (size range is 1-1/2 to 18-inch pipe and up to 18-inch structural beans). The MITER MARKER has been completely redesigned and is sold in a sturdy polyoropylene lockable case (p/n 8902) for lasting protection.
MITER MARKER include Flange Wizard®’s new “sight unseen” magnets built right into the main base legs. This keeps the tool secure while laying out those precision angles and saddles. The unique design of the tool allow you to telescope out over existing welds to layout angles or change the angles of pipe fittings to meet your special needs. The marking arm is completely separate from the main body. It has its own 360° rotating shaft with a built-in leveling vial. The arms have spring-loaded joints for smooth and precision operation for years of trouble-free service. Structural beam layouts and marking angles or saddles on pipe and tubing are a snap with the MITER MARKER. (Structural Adapter p/n 8311 is included).
There are no extra combination adapters to buy when purchasing the MITER MARKER as they are engineered right in the body of the tool. Replace multiple templates with just one tool.
#65007 Multi-Hole Imager – The Multi-Hole Imager is Flange Wizard®’s newest layout tool. The strong “on and off” magnet makes positioning on a round, flat, or irregular surface easy. A “bull’s eye” circular levelling vial is built in the main tower of the Multi-Hole Imager to assist in levelling the tool as required. The Multi-Hole Imager will layout round or elongated holes (ellipse) on flat material or pipe to match laterals at compound angles or at 90°. The main arm is adjustable and notched to keep it centered with the tower for true layouts.
A protractor, with adjustable shaft and sliding marking arm, fits in the main arm of the Imager allowing for layout of elliptical holes in header pipe for matching compound pipe laterals coming in to the header. It will layout matching holes in pipe for 90° saddle branches. The Imager is great for round holes in plate or elongated holes when coming in at an angle. It also can replace multiple templates with just one tool. The Multi-Hole Imager is sold in a sturdy polypropylene case (p/n 8903) for protection between jobs. A Spring Buckle Strap (p/n 5010) is available to hold Imager in position for non-magnetic surfaces.
Marks 3/4′ to 20′ holes in plate with vertical shaft at 90°.
#70001 Angle Burning Guide with magnetic base for use with conventional or plasma torch to assist in making excellent angle or straight cuts every time. Also use as a protractor or multi-angle tri-square. Guide will hold any standard square as well as most straight edges.
NOTE: Protective carrying case p/n 8903 can be ordered separately (16” x 6” x 3”)
#70501 A must for anyone using a cutting torch and wants to keep their tip at the proper burning height at all times. It assists in making more uniform cuts and keeps cutting tips from being damaged. Slide the Standoff over the cutting tip and against the bottom of the torch nut and tighten the set screw.
USE WITH: Magnetic Torch Guides and Magnetic Blocks.
# 72800 (small 11″ span = 22” circle)
# 72805 (Standard 25″ span = 50” circle)
# 72810 (Extra Large 50” span = 100″ circle)
Machined from rustproof aluminum material, then anodized for lasting protection. For laying out your smallest circles to the large ones (up to 100” in diameter). Arms are precisely aligned with spring tension joints to guarantee accuracy and rigidity for years of continued service. The holder accommodates flat or round soap stone and pencils. Small and medium models fold to pocket size. The Extra Large model can be adjusted tight in the center to eliminate any movement while marking large radius’s or circles.
#89754 Magnetic Tape Holder has been designed with no removable parts and works with most industrial measuring tapes. It is a great little magnetic pocket level and a third hand when doing difficult measuring jobs while working alone. Secure the end of your tape while laying out close tolerance measurements from the end or the center of your material.
This tool is machined from aluminum and anodized for a protective finish. A strong 25 pound pull magnet set in epoxy secures the tape holder to your work. There is a rare earth magnet at one end of the tool to hold your tape measure in place while laying out difficult jobs. Size is 5/8 inch square by 4 inches long.
#CW-300 This cutting attachment is a must for anyone who cuts small to medium holes in plate or pipe. It is especially handy for cutting out the holes for matching saddle cuts, weldolets and threadolets. Made of finished high quality steel. The universal bushing will adapt to any size or make of conventional cutting torch.
Will cut holes from 5/8” to 8” in diameter (recommend Chariot Cutting Guide P/N 24219 for larger holes). Simply slide the center pen along the hex arm to attain the proper radius of hole desired. Place the sharpened point in your center mark and you are ready to cut.
#L-2 Shirt pocket size (1-1/2” x 2-3/8” x 5/8” thick) degree dial level makes it easy to establish angles, set tanks, layout keyways and measure decline or slope. The level body is permanently marked in 2.5° increments and numbered every 10 degrees. It has strong magnets in the base for easy hands-off use and can even hold the end of a tape measure for solo use. Great level for getting angles on hard to reach pipe or structural steel details.
On the back side of the tool is a PITCH/LEVEL DEGREES scale for easy referencing. Tool is machined from aluminum and anodized for a protective finish.
MM-501 in carrying case
#MM-501 (size range is 8 to 48-inch pipe or structural steel beams). Structural beam layouts and marking angles or saddles on pipe and tubing are a snap with the Master Marker. Replace multiple templates just with one tool. Magnets are built right into the main base legs to keep tool secure while laying out those precision angles and saddles. The Master Marker comes with a unique design that allows you to telescope out over existing welds to layout angles or change the angles of pipe fittings to meet your special needs. .
REDESIGNED to include these standard functions:
There are no extra combination adapters to buy when purchasing the MASTER MARKER as it is engineered right in the body of the tool. It is machined from quality aluminum material then anodized for lasting protection.
#PG-601-1.xxxx includes Bushing
#PG-601-1.xxxx* must state bushing size
Assists in cutting holes from 5/8” to 36” in diameter. (Click here to for bushing guide). Cut medium to large circles by using just one wheel to balance tool.
For straight and irregular cuts using wheels to hold torch stable.
Wheels are not necessary when cutting holes 5/8” to 8” in diameter.
15-1/2” Extension hex arm (p/n 3311-EX) is available for larger jobs.
Magnetic Base with Suction Cups (p/n 77350) serves as a third hand when cutting large holes.
WARNING: Never use the magnetic base or suction cups when cutting small holes. The heat will damage the magnets or the rubber suction cups.
#PP-200 One of the finest levels available in the welding industry. Designed to give years of quality service. Extra strong magnets hold it firmly to any steel surface. There are two (2) stationery vials placed at 90° angles of each other and can be read from any surface of the level. If vials are damaged, just remove them and replace with a new one (VIAL REPAIR KIT p/n 5102 includes 2 vials and a tube of sealant). The dial is in 2.5° increments with spring tension for smooth operation. On the back side of the tools is a ROOF PITCH/LEVEL DEGREES scale for easy referencing. Tool is machined from aluminum and anodized for a protective finish. Size is 1.5” wide x 9” long.
Flange Wizard® listens to our customers. The newest product entry to the levelling and layout tools is the STANDARD POCKET LEVEL. This 9.0″ long x 1.5″ wide magnetic level has three-position levelling
The STANDARD POCKET LEVEL is machined from aircraft quality aluminum and anodized for lasting beauty and protection. It is manufactured with the same high quality as our POCKET PRO LEVEL (PP-200) but designed for the tradesman who does not need the protractor degree dial. Like all of our other quality leveling tools, the S
WW-16 Small wrap is 30”L x 2-5/8” W for pipes 1” to 6” in diameter.